large-pages option is broken) from next-mr to trunk-bugfixing.
Original revision:
------------------------------------------------------------
revision-id: vvaintroub@mysql.com-20100416134524-y4v27j90p5xvblmy
parent: luis.soares@sun.com-20100416000700-n267ynu77visx31t
committer: Vladislav Vaintroub <vvaintroub@mysql.com>
branch nick: mysql-next-mr-bugfixing
timestamp: Fri 2010-04-16 15:45:24 +0200
message:
Bug #52716 Large files support is disabled, large-pages option is broken.
Correct typo: large pages option was tied to wrong variable opt_large_files,
instead of opt_large_pages.
------------------------------------------------------------
BUG#54872 MBR: replication failure caused by using tmp table inside transaction
Changed criteria to classify a statement as unsafe in order to reduce the
number of spurious warnings. So a statement is classified as unsafe when
there is on-going transaction at any point of the execution if:
1. The mixed statement is about to update a transactional table and
a non-transactional table.
2. The mixed statement is about to update a temporary transactional
table and a non-transactional table.
3. The mixed statement is about to update a transactional table and
read from a non-transactional table.
4. The mixed statement is about to update a temporary transactional
table and read from a non-transactional table.
5. The mixed statement is about to update a non-transactional table
and read from a transactional table when the isolation level is
lower than repeatable read.
After updating a transactional table if:
6. The mixed statement is about to update a non-transactional table
and read from a temporary transactional table.
7. The mixed statement is about to update a non-transactional table
and read from a temporary transactional table.
8. The mixed statement is about to update a non-transactionala table
and read from a temporary non-transactional table.
9. The mixed statement is about to update a temporary non-transactional
table and update a non-transactional table.
10. The mixed statement is about to update a temporary non-transactional
table and read from a non-transactional table.
11. A statement is about to update a non-transactional table and the
option variables.binlog_direct_non_trans_update is OFF.
The reason for this is that locks acquired may not protected a concurrent
transaction of interfering in the current execution and by consequence in
the result. So the patch reduced the number of spurious unsafe warnings.
Besides we fixed a regression caused by BUG#51894, which makes temporary
tables to go into the trx-cache if there is an on-going transaction. In
MIXED mode, the patch for BUG#51894 ignores that the trx-cache may have
updates to temporary non-transactional tables that must be written to the
binary log while rolling back the transaction.
So we fix this problem by writing the content of the trx-cache to the
binary log while rolling back a transaction if a non-transactional
temporary table was updated and the binary logging format is MIXED.
mysqld-debug.exe in 5.5.3 on windows
Fix:
- Do not rename PDB, install mysqld.pdb matching
mysqld-debug.exe into bin\debug subdirectory
- Stack tracing code will now additionally look in
debug subdirectory of the application directory
for debug symbols.
- Small cleanup in stacktracing code: link with
dbghelp rather than load functions dynamically
at runtime, since dbghelp.dll is always present.
- Install debug binaries with WiX
This bug is a consequence of WL#5349, as the
default storage engine was changed.
The fix was to explicitly add an ENGINE
clause to a CREATE TABLE statement, to
ensure that we test case preservement on
MyISAM.
Bug#47633 - assert in ha_myisammrg::info during OPTIMIZE
The server crashed on an attempt to optimize a MERGE table with
non-existent child table.
mysql_admin_table() relied on the table to be successfully open
if a table object had been allocated.
Changed code to check return value of the open function before
calling a handler:: function on it.
DML flow and SAVEPOINT
The problem was that replication could break if a transaction involving
both transactional and non-transactional tables was rolled back to a
savepoint. It broke if a concurrent connection tried to drop a
transactional table which was locked after the savepoint was set.
This DROP TABLE completed when ROLLBACK TO SAVEPOINT was executed as the
lock on the table was dropped by the transaction. When the slave later
tried to apply the binlog, it would fail as the table would already
have been dropped.
The reason for the problem is that transactions involving both
transactional and non-transactional tables are written fully to the
binlog during ROLLBACK TO SAVEPOINT. At the same time, metadata locks
acquired after a savepoint, were released during ROLLBACK TO SAVEPOINT.
This allowed a second connection to drop a table only used between
SAVEPOINT and ROLLBACK TO SAVEPOINT. Which caused the transaction binlog
to refer to a non-existing table when it was written during ROLLBACK
TO SAVEPOINT.
This patch fixes the problem by not releasing metadata locks when
ROLLBACK TO SAVEPOINT is executed if binlogging is enabled.
Accidental change in compile-time definitions for FreeBSD
Revert the accidental setting of "HAVE_BROKEN_REALPATH"
on current versions of FreeBSD,
do it for both autotools ("configure.in")
and cmake ("cmake/os/FreeBSD.cmake").
use limit efficiently
Bug #36569: UPDATE ... WHERE ... ORDER BY... always does a
filesort even if not required
Also two bugs reported after QA review (before the commit
of bugs above to public trees, no documentation needed):
Bug #53737: Performance regressions after applying patch
for bug 36569
Bug #53742: UPDATEs have no effect after applying patch
for bug 36569
Execution of single-table UPDATE and DELETE statements did not use the
same optimizer as was used in the compilation of SELECT statements.
Instead, it had an optimizer of its own that did not take into account
that you can omit sorting by retrieving rows using an index.
Extra optimization has been added: when applicable, single-table
UPDATE/DELETE statements use an existing index instead of filesort. A
corresponding SELECT query would do the former.
Also handling of the DESC ordering expression has been added when
reverse index scan is applicable.
From now on most single table UPDATE and DELETE statements show the
same disk access patterns as the corresponding SELECT query. We verify
this by comparing the result of SHOW STATUS LIKE 'Sort%
Currently the get_index_for_order function
a) checks quick select index (if any) for compatibility with the
ORDER expression list or
b) chooses the cheapest available compatible index, but only if
the index scan is cheaper than filesort.
Second way is implemented by the new test_if_cheaper_ordering
function (extracted part the test_if_skip_sort_order()).
The default storage engine is changed from MyISAM to
InnoDB, in all builds except for the embedded server.
In addition, the following system variables are
changed:
* innodb_file_per_table is enabled
* innodb_strict_mode is enabled
* innodb_file_format_name_update is changed
to 'Barracuda'
The test suite is changed so that tests that do not
explicitly include the have_innodb.inc are run with
--default-storage-engine=MyISAM. This is to ease the
transition, so that most regression tests are run
with the same engine as before.
Some tests are disabled for the embedded server
regression test, as the output of certain statements
will be different that for the regular server
(i.e SELECT @@default_storage_engine). This is to
ease transition.
line exceeds the limit
The number and/or names of our files for the main test suite
(contents of "mysql-test/t/") now exceeds the command line
length limit on AIX.
Solve the problem by using separate "cp" commands for the
various file name extensions.
